Search results for 'red'

Tempered Steel Dry Point Needle No 49A Learn More

A red amorphous powder consisting of ferric chloride oxide. Used as a colourant for ceramic glazes. Also used in polishing glass, metal, or gems. Also known as jeweller's rouge. Learn More

Cornelissen Etching Press T52100B 52 x 100 cm, Bed size: 52 x 100 cm, Upper Roller Diameter: 110 mm, Lower Roller Diameter: 110mm, Weight: 83 kg. Etching press base: 56 x 44 cm. Please call Cornelissen for more details. Delivery to your address usually takes up to 4 weeks to UK & EU countries and 6 weeks to USA after the order is placed. Please be aware these goods are heavy and it is the customer’s responsibility to check measurements for delivery before orders are placed and to be able to receive the goods over two days.

 

Learn More

Tento easy grip carving set. This set comes in a plastic box and contains 5pcs, including; 7.5mm Hangi-toh (knife), 7.5mm Aisuki (flat), 6mm Komasuki (U), 3mm Komasuki (U), 3mm Sankatu-toh (V). These are pencil style tools with a soft easy grip, non-slip rubber ferrule and plastic handle. The handle is longer when compared to the traditional tools, perfect as an introduction to Mokuhanga printing. Learn More

The Hangi-toh is a cutting knife with a bevelled edge. It is used to outline areas to be kept. This is the most useful tool for the Mokuhanga artist. The tool is designed to be held blade down at roughly 90 degree angle with the flat edge of the blade towards line to be kept and the bevelled edge in the area to be carved away. A small amount of pressure is excised by placing thumb over the end of the handle slightly to the left and blade tilted to the right (if you are right handed) so that you may see the blade running down the line as you work, the blade should be guided with the other hand though care is needed not to apply too much pressure. This is the traditional method of holding the tool and, for this reason right and left handed tools are required. (Please note, left handed tools can be ordered by telephone and will take 4-6 weeks to arrive). The blade may be removed and sharpened by slipping off the ferrule. Learn More

Easy Grip Crible Point Sharp #93 A traditional crible point for creating indentations in the plate. 120mm length dot. -Heavy duty tool with tapered shaft ending in a small dot -Tempered steel Crible points are designed to put small holes or indentations in the surface of the plate, creating a dotted or stippled pattern. Learn More

Sosaku inking brush for working the pigments and glue paste onto the carved block for printing. These are made from horse hair and are traditionally prepared by splitting and softening the hair on shark-skin or sandpaper before printing. Brushes come in 3 sizes. Learn More

Used in printmaking. Imparts softness and greasiness. An ingredient for producing soft etching ground. Learn More

Cornelissen Press T52100, Bed size: 52 x 100 cm, Upper Roller Diameter: 157 mm, Lower Roller Diameter: 157mm, Weight: 106 kg. Etching press base: 58 x 63 cm. We offer press demonstrations for this model. Please call Cornelissen for more details. Delivery to your address usually takes up to 4 weeks to UK & EU countries and 6 weeks to USA after the order is placed.

Learn More

Tool set with denim case. Set contains 7pcs, including; 7mm Aisuki (flat), 8mm Hangi-toh (knife), 4mm Aisuki (flat), 6mm Komasuki (U), 3mm Komasuki (U), 4mm Sankatu-toh (V), 10mm Komasuki (U). These are pencil style tools with an imitation wooden handle that is longer when compared to the traditional tools, perfect as an introduction to Mokuhanga printing. Learn More

Type of print: General Intaglio techniques and Monotype. Plate thickness needs to be no higher than 1mm. YTI18 - Width of roller 18cm, Upper roller diameter 35mm, Lower roller diameter 35mm. YTI26 - Width of roller 25cm, Upper roller diameter 35mm, Lower roller diameter 35mm **please note - blankets not included** Learn More

Easy Grip Crible Point Squat #94 Heavy duty tool with tapered shaft ending in a point Crible points are designed to put small holes or indentations in the surface of the plate, creating a dotted or stippled pattern. Learn More

Sosaku inking brush for working the pigments and glue paste onto the carved block for printing. These are made from horse hair and are traditionally prepared by splitting and softening the hair on shark-skin or sandpaper before printing. Brushes come in 3 sizes. Learn More

Sosaku inking brush for working the pigments and glue paste onto the carved block for printing. These are made from horse hair and are traditionally prepared by splitting and softening the hair on shark-skin or sandpaper before printing. Brushes come in 3 sizes. Learn More